Video

ASME BPE 2007 PDF

Posted On
Posted By admin

ASME BPE (Revision of ASME BPE). Bioprocessing. Equipment. AN AMERICAN NATIONAL STANDARD. Three Park Avenue. Buy ASME BPE Bioprocessing Equipment from SAI Global. No reproduction may be made of this material without written consent of ASME. ASME BPE (Revision of ASME BPE) Bioprocessing.

Author: Gromuro Meztihn
Country: Burkina Faso
Language: English (Spanish)
Genre: History
Published (Last): 24 May 2006
Pages: 120
PDF File Size: 16.46 Mb
ePub File Size: 16.91 Mb
ISBN: 191-6-56186-772-5
Downloads: 34605
Price: Free* [*Free Regsitration Required]
Uploader: Malajind

Asmd necessary, increases in height should be achieved by vertical risers see Fig. Dvorscek, Abbott Laboratories M. All internal surfaces shall be passivated. Cirillo, Jacobs Field Services R. It is preferred that an external, piping mounted relief device Copyright c by the American Society of Mechanical Engineers.

ASME BPE Guidelines for Pharmaceutical Equipment

The nameplates should be attached and sealed or attached with a corrosion-resistant wire loop. Typical Ball Valve Configuration. Acceptance Criteria for Tube-Attachment Welds. The purpose of this Part is to create a design framework using proven practices, for maintaining clean and sterile process systems.

User Basic Design Requirement.

The conformance of material should be explicitly stated e. SD-4, illustrations a and d. This is usually achieved at a velocity of 5 fps 1.

If screwed fittings are used, an O-ring or gasketed fitting, where the inside diameter I. Organizations that are authorized to use Symbol Stamps for marking items or constructions that have been constructed and inspected in compliance with ASME codes and standards are issued Certificates.

  LECHUGA HIDROPONICA PDF

Valve seals should comply with Part SG of this Standard. A tube or pipe installed in the horizontal plane is said to slope if one end is positioned higher than the other. Cirillo, Jacobs Field Services B. O-ring grooves should be shaped in accordance with the O-ring manufacturer recommendation for functionality.

ASME BPE – Wikipedia

Operating conditions include heat-up, hold, and cooldown. The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate.

In all cases sufficient annular space to allow access for CIP coverage shall be provided. A thermal switch, timer, momentary switch, IR filter, or some other suitable means should be considered.

Examples of sealed fasteners are shown in Fig.

ASME BPE Bioprocessing Equipment_图文_百度文库

If a smaller annular space is provided, other methods of cleaning this space should be provided, such as holes in the dip tube that CIP the nozzle spacing. Methods of separation used in industry are a removable spool piece b U-bend transfer panel c double block-and-bleed valve system see Fig. The test shall be performed by spraying a dye e. Elevated equipment under open frames should have a minimum clearance of 6 in.

  DOMNUL TRANDAFIR DE MIHAIL SADOVEANU PDF

Pure Steam a The clean steam distribution system shall have adequate provision to remove air during start-up and normal operations.

General Provisions for Seals in Bioprocessing Service: Where used, the additions of these components will require a blowdown to ensure drainability. Inspection, Examination, and Testing. Jumpers may include drain valves xsme pressure indicators for safety or operating purposes.

It is the responsibility of the end-user to establish complaince with applicable standards e. When mitered joints are used, they shall be designed and fabricated in accordance with the appropriate codes see Fig. Steam trap bodies shall have an internal surface finish excluding the bellows assembly as agreed to by all parties.

Participation by federal agency representative s or person s affiliated with industry is not to be interpreted as government or industry endorsement of this code or asmr. March 21, The next edition of this Standard is scheduled for publication in The installer and user shall ensure that proper orientation is achieved.

Open Cross-Sectional Lip Seal.