ASTM B367 PDF
Originally approved in Last previous edition approved in as B – 2 For referenced ASTM standards, visit the ASTM website. ASTM B(). Standard Specification for Titanium and Titanium Alloy Castings. standard by ASTM International, 11/01/ View all product details. ASTM B Standard Specification for Titanium and Titanium Alloy Castings.
|Published (Last):||1 July 2015|
|PDF File Size:||13.49 Mb|
|ePub File Size:||3.98 Mb|
|Price:||Free* [*Free Regsitration Required]|
Examination of Weld Preparation S3. Current edition atm Aug. Materials and Manufacture 5. The decision for stress relieving shall be made by the producer, unless otherwise agreed upon. The chemical composition determined shall conform to the analysis in Table 1 within the check analysis variations shown in Table 2 or shall be subject to rejection by the purchaser. Historical Version s – view aastm versions of standard.
Small size castings may be such that marking must be limited consistent with the available area.
The stressrelief cycle shall be in accordance with 7. If the results of the retest conform to the speci? This is in accordance with the round-off method of Practice E Hardness shall be determined in the as-cast condition unless otherwise speci?
Details of the supplementary requirements shall be agreed upon by the producer and purchaser. The values given in parentheses are for information only. Hardness values reported shall be representative of the base metal of the castings and not of any surface contamination due to mold-metal interactions. Only original conforming test results or the conforming retest astj shall be reported to the purchaser.
The stress-relief cycle shall be in accordance with 7.
ASTM B367 Titanium Impeller of Titanium Casting GB/T 15073
The examination shall be in accordance with Practice E Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Time at temperature shall be a minimum of 1? A number in parentheses indicates the year of last reapproval. When discontinuities exceed the acceptance limits, all castings in the lot shall be examined according to Category II.
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Properties shall be determined in the as-cast condition unless otherwise speci? Link to Active This link will always route to the current Active version of the standard. Last previous edition B — Materials for this specification shall be melted by conventional processes used for reactive metals such as consumable electrode and induction-slag, plasma arc, induction-skull, and electron beam melting processes.
This abstract is a brief summary of the referenced standard. Other surface discontinuities shall meet the visual acceptance standards speci?
Repair by Welding 9. If the pattern is supplied by the purchaser, the dimensions of the casting shall be as predicted by the pattern. The frequency of the retest will double the initial number of tests. Types and degrees of discontinuities considered shall be judged by the Reference Radiographs E Areas to be inspected, methods and types of liquid penetrants to be used, developing procedure, and basis for acceptance shall be agreed upon between the producer and the purchaser.
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters. Tensile Strength, min, 0. The test report shall contain the results of the actual chemical analysis and other tests speci?
After heat treatment, the castings should be cooled in air or in the furnace to ambient temperature unless otherwise agreed upon between the purchaser and producer. Need not be reported. Unalloyed titanium plus 0. Dimensional tolerances shall be included on the casting drawing, 4. The results shall conform to the requirements speci? Liquid Penetrant Examination S2. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?
Extent of examination and the basis for acceptance shall be agreed b376 by the producer and the purchaser. The surface of the castings shall be free of adhering mold material, scale, cracks, and hot tears as determined by visual inspection.
China Titanium Investment Casting Pump Casing ASTM B – China Pump, Pump Casing
Temperature, time at temperature, and atmosphere shall be as agreed upon between the producer and the purchaser. This specification covers the standard requirements for titanium and titanium alloy castings intended for adtm corrosion resistant and industrial applications.
Typical methods include the consumable electrode and induction-slag, plasma arc, induction-skull, and electron beam melting processes. Therefore product analysis for elements not listed in Table 1 shall not be required unless speci? If the results for the retest fail to conform to the speci? The materials shall undergo chemical, pour, and product analysis to determine the chemical composition which shall conform to the requirements for nitrogen, carbon, hydrogen, iron, oxygen, aluminum, vanadium, tin, ruthenium, palladium, cobalt, molybdenum, chromium, nickel, niobium, zirconium, silicon, and titanium.