Video

HCNW3120 DATASHEET PDF

Posted On
Posted By admin

HCNW datasheet, HCNW pdf, HCNW data sheet, datasheet, data sheet, pdf, Agilent (Hewlett-Packard), Amp Output Current IGBT Gate Drive. Broadcom HCNW available from 7 distributors. Explore Optoelectronics on Octopart: the fastest source for datasheets, pricing, specs and availability. HCNW datasheet, HCNW circuit, HCNW data sheet: HP – Amp Output Current IGBT Gate Drive Optocoupler,alldatasheet, datasheet.

Author: Sajar Tot
Country: Bermuda
Language: English (Spanish)
Genre: Literature
Published (Last): 2 March 2012
Pages: 227
PDF File Size: 2.33 Mb
ePub File Size: 20.67 Mb
ISBN: 363-4-92956-319-6
Downloads: 84550
Price: Free* [*Free Regsitration Required]
Uploader: Motaur

Documents Flashcards Grammar checker. The LED is optically coupled to an integrated circuit with a power output stage. The high operating voltage range of the output stage provides the drive voltages required by gate controlled devices. Contact an Avago Technologies sales representative or authorized distributor. To order, choose a part number from the part number column and combine with the desired option from the option column to form an order datashet.

Option data sheets are available. Contact your Avago Technologies sales representative or authorized distributor for information. Minimum External Tracking L Creepage 7. These dimensions are needed as a starting point for the equipment designer when determining the circuit insulation requirements. However, once mounted on a printed circuit board, minimum creepage and clearance requirements must be met as specified for individual equipment standards.

Datqsheet creepage, the shortest distance path along the surface of a printed circuit board between the solder fillets of the input and output leads must be considered.

HCNW3120 Datasheet PDF

There are recommended techniques hcne3120 as grooves and ribs which may be used on a printed circuit board to achieve desired creepage and clearances. Creepage and clearance distances will also change depending on factors such as pollution degree and insulation level. Maintenance of the safety data shall be ensured datasheft means of protective circuits. See Applications section for additional details on limiting IOH peak. In this test, VOH is measured with a dc load current.

  DIAGNOSTIC ULTRASOUND PRINCIPLES AND INSTRUMENTS KREMKAU PDF

Pins 1 and 4 need to be connected to LED common. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating.

HCPL-3120/J312, HCNW3120

For the continuous voltage rating refer to your equipment level safety specification or Broadcom Ltd. Device considered a two-terminal hcna3120 Temperature Figure 3 VOH vs. This results in lower peak currents more margin than predicted by this analysis. When negative gate drive is not used VEE in the previous equation is equal to zero volts.

HCNW Datasheet(PDF) – Agilent(Hewlett-Packard)

The thermal resistance values given in this model can be used to calculate the dayasheet at each node for a given operating condition. However, this shield does not eliminate the capacitive coupling between the LED and optocoupler pins 5—8 as shown in Figure This capacitive coupling causes perturbations in the LED current during common mode transients and becomes the major source of CMR failures for a shielded optocoupler.

Techniques to keep the LED in the proper state are discussed in the next two sections. This is achieved by overdriving the LED current beyond the input threshold so that it is not pulled below the threshold during a transient.

  FONTES HISTRICAS CARLA PINSKY PDF

HCNW Datasheet(PDF) – AVAGO TECHNOLOGIES LIMITED

Figure 33 is an alternative drive circuit which, like the recommended application circuit Figure 25does achieve ultra high CMR performance by shunting the Datashee in the off state. Dead time is the time period during which both the high and low side power transistors Q1 and Q2 in Figure 25 are off. Any overlap in Q1 and Q2 conduction will result in large currents flowing through the power devices between the high and low voltage motor rails.

To minimize dead time in a given design, the turn on of LED2 should be delayed relative to the dataaheet off of LED1 so that under worst-case conditions, transistor Q1 has just turned off when transistor Q2 turns on, as shown in Figure Delaying the LED signal by the maximum propagation delay difference ensures that the minimum dead time is zero, but it does not tell a designer what the maximum dead time will be.

Note that the propagation delays used to calculate PDD and dead time are taken at equal temperatures and test conditions since the optocouplers under consideration are typically mounted in close proximity to each other and are switching identical IGBTs.

All other brand and product names may be trademarks of their respective companies. Data subject to change. AVEN — March 21, Lab 9 in this note.