IEC 60605 PDF
IEC Equipment Reliability Testing – Part 4: Statistical Procedures for Exponential Distribution – Point Estimates, Confidence Intervals, Prediction. Buy IEC EQUIPMENT RELIABILITY TESTING – PART 4: STATISTICAL PROCEDURES FOR EXPONENTIAL DISTRIBUTION – POINT ESTIMATES. Buy IEC Ed. Equipment reliability testing Part 4: Statistical procedures for exponential distribution – Point estimates, confidence intervals, prediction.
|Published (Last):||13 August 2018|
|PDF File Size:||18.12 Mb|
|ePub File Size:||12.41 Mb|
|Price:||Free* [*Free Regsitration Required]|
Ic are several reliability growth models available, the power law model being one of the most widely used. Part 1- Section One, Two and Three. Tests for the validity of the constant failure rate or constant failure intensity assumptions.
OVE webshop – IEC
Describes procedures to estimate the parameters of the power law uec along with confidence intervals for failure intensity, and prediction intervals for the time to future idc along with a test of goodness of fit to data from repaired items. This part of IEC provides a general procedure for design of test cycles, where no applicable preferred test cycles can be found in IEC Some of the 50 IEC publications are:. These procedures are applicable whenever it is necessary to verify these assumptions.
This standard also addresses the collection, analysis and presentation of maintainability related data, which may be required during, and at the completion of, design and during item production and operation.
This document was withdrawn in and replace by IEC for Reliability stress screening-Part 1: Tests which include cycles designed according to this standard are not intended to replace ordinary tests such as qualification tests, functional pe rformance tests and environmental tests.
Describes procedures for compliance test plans for success ratio or failure ratio tests where each trial is statistically independent. Subscription pricing is determined by: If the document is revised or amended, you will be notified by email.
“Reliabilty and dependability standards are described.”
Guide to the specification of dependability requirements. Testability and diagnostic testing. Describes the use of failure rate data for reliability prediction of components eic electronic equipment including the effects of complexity, stress models for conversion.
This standard is not included in any packages. Your Alert Profile lists the documents that will be monitored.
Applicable oec detailed planning and implementation of a dependability program to meet specific product needs. The failure modes defined in ISO Describes guidelines for exposure and removal of weaknesses in hardware and software items to make reliability grow and mathematical modeling is outlined briefly.
Replaced by IEC Ed 1. Design of test cycles. Application guide- Section 6: The main changes with respect to the previous edition are as follows: Describes plans and procedures for inspection by attributes. The following main categories of data are to be collected: This part of IEC provides a general introduction to the concept of life cycle costing and covers all applications. Take the smart route to manage medical device compliance.
BS IEC 60605-4:2001
As the voice of the U. Describes Markov analysis methods for modeling maintenance strategies along with failure restorations events displayed in a pictorial way. Verification and collection, analysis and presentation of data.
Describes aspects of verification necessary to ensure that the specified maintainability requirements of an item have been met and provides suitable procedures and test methods.
Need more than one copy? Deals with dependability performance issues including availability performance, reliability performance, maintainability performance, and maintenance support performance.
Equipment for stationary use in weather protected locations — High degree of simulation. Also refer to following documents for data collection: This standard provides guidance for the collection and presentation of data relating to the reliability of electronic components and their reliability characteristics.
This standard does not cover guidance on how to plan, perform. Essai de fiabilite des equipements.
Describes guidelines for selecting and implementing risk analysis techniques for quality and consistency in planning and execution for risk analysis. Describes a general introduction to project risk management, its sub-processes and influencing factors, and provides guidelines for implementing risk management at various phases of a project. Describes numerical methods for performing a Weibull goodness of fit test for two-parameter Weibull distribution using maximum likelihood methods.
Describes maintainability requirements and related design and use parameter, and discusses some activities necessary to achieve the required maintainability characteristics and their relationship to planning of maintenance.
Part 4- Section 8: Endurance testing, Statistical methods of analysis, Confidence intervals, Estimation, Exponential distribution, Electrical testing, Reliability, Ief tolerance intervals, Statistical testing, Performance.